ここから本文です
TWO:"'These allegations of the reporter of De Tijd caused the authorities to institute inquiries, and the following is now stated with regard to the alleged events:
Classification by type of system
1natural circulation external heating pipe type
2natural circulation calandria type
3forced circulation type
4falling-film type
5rising film type
6jacket type
7coil type
Classification by method of operation
1single effect evaporator system
2multiple effect evaporator system
3auto-vapor mechanical compression system
4auto-vapor ejector compression system
5multistage flash system

After taking into consideration of the physical and chemical property of solutions, the desired design conditions, and available utilities, we select the most suitable type of system by utilizing our years of experience and excellent results.
In addition, we can offer designs and manufacturing services that take into careful consideration compactness, energy-efficiency, and automatization.

THREE:Machinery subjected to destructive wear, and to be operated at a distance from machine shopslocomotive engines for exampleif not constructed with standard dimensions, may, by the detention due to repairing, cause a loss and inconvenience equal to their value; if a shaft wheel bearing, or even a fitted screw bolt is broken, time must be allowed to make the parts new; and in order to fit them, the whole machine, or such of its details as have connection with the broken parts, must be taken to a shop in order to fit by trial.

While standard calandria type evaporation systems are widely used as the typical concentration evaporator by the various food and chemical industries, we have delivered many of those systems as finishing concentration evaporators especially for sugar solutions and starch syrups.

THREE:"Well, it seems that the civilians cannot understand that only soldiers may fight soldiers, and for that reason the whole place has been set on fire."In planing and turning, the tools require no exact form; they can be roughly made, except the edge, and even this, in most cases, is shaped by the eye. Such tools are maintained at a trifling expense, and the destruction of an edge is a matter of no consequence. The form, temper, and strength can be continually adapted to the varying conditions of the work and the hardness of material. The line of division between planing and milling is fixed by two circumstancesthe hardness and uniformity of the material to be cut, and the importance of duplication. Brass, clean iron, soft steel, or any homogeneous metal not hard enough to cause risk to the tools, can be milled at less expense than planed, provided there is enough work of a uniform character to justify the expense of milling tools. Cutting the teeth of wheels is an example where milling is profitable, but not to the extent generally supposed. In the manufacture of small arms, sewing machines, clocks, and especially watches, where there is a constant and exact duplication of parts, milling is indispensable. Such manufactures are in some cases founded on milling operations, as will be pointed out in another chapter.
  • Enables flexible operation with little influence from variations in load and raw solution concentrations because of an adequate amount of solution being held within the system. These systems are also suitable for batch type burning evaporators.
  • Concentrations can be controlled within product specifications by the cascade control using the concentrations of concentrated solution and the raw solution supply and also by the arithmetic control of raw solution concentrations, etc. (Result for sugar solutions: 75±0.2wt%)
  • High-viscosity solutions and solutions that may crystallize can also be utilized by installing a propeller in the evaporator as a forced circulation system.
THREE:Charlton nodded. He was a man of few words. He said nothing when Lawrence gave him a pair of goloshes to put over his boots, and in silence the two set out for Raven Street. The place was practically deserted as they came to the house, so that to enter without being seen was a matter of no difficulty.

This is a process example of a device that continuously and simultaneously concentrates two types of waste liquid with a single high-efficiency steam compressor.

THREE:In ages past, various attempts were made to find some constant in nature on which measures could be based. Some of these attempts were ludicrous, and all of them failures, until the vibrations of a pendulum connected length and space with time. The problem was then more easy. The changes of seasons and the movement of heavenly bodies had established measures of time, so that days, hours, and minutes became constants, proved and maintained by the unerring laws of nature."Here's your young man," she said presently. "He didn't want to come, but I made a special journey and persuaded him. Never hide yourself at times like this."
  • By evaporating the steam using a mechanical compressor and reusing it, almost no heating steam is alomost required except the time of start-up, so large energy savings can be expected.
  • By combining with a thin film falling heat exchanger that does not raise the boiling point due to the liquid depth, it is possible to utilize the temperature difference of the compressor at the maximum.
  • Since the residence time and heating time are short and the holding amount is small, starting and stopping can be performed in a short time.
  • It will prevent scale adhesion in the can that the evaporator is divided into two parts, and that the supply of the undiluted solution is alternately switched over a fixed period of time to perform heat concentration.